We are rewarded for products purchased through some of the links in this article.
Bathroom and kitchen floor tiles wear out quickly and need updating. From wall tiles to floor tiles, follow our easy DIY tutorial to apply tiles and tiles yourself so you can fall in love with your home again.
And since we all like to be more adventurous with bathroom tile ideas, it would be great if you knew how to sew them yourself, so update time is a great time to get the job done. . .
Whether you’re adding a colorful fire hazard to your kitchen or installing new floors in your bathroom, you need grout tiles to protect them from dust and moisture.
If you are considering laying bathroom floors, we recommend that you focus on this important step. Because if your tiles are properly protected, they will be easier to clean, more resistant to stains, and more resistant to bacteria and mold.
Fortunately, grout is quick and easy to apply, and by following our easy step-by-step instructions for gluing (and gluing) tile, you’re sure to have a professional finish in no time. .
How to Sew Bricks
David Talbot, Configuration Manager at Craven Dunnill Jackfield advises: “Before you start gluing, make sure the tile joints are free of dust, glue, sealant, moisture or other debris.”
It then goes on to say: “If the tiles you choose are porous, cracked, metallic glazed or similar, check to see if they need to be sealed before gluing.”
what do you need
- scraper or spreader
- A bucket of mushrooms
Most DIY stores and online stores sell all kinds of mortars and everything you need.
What do you use to seal the bricks?
There are four main types of grout:
- grout It is often used for do-it-yourself brick projects. It is weaker than epoxy but easier to handle.
- epoxy mortar Slightly more expensive than others, but effective for tiles that require high water resistance, such as bathroom floor tiles.
- Rubber Modified Sand Cement Mortar Similar to cement mortar, but with higher water resistance and adhesion, ideal for bathrooms and countertops.
- sealing mortar Pressed out of the pipe by hand or with a glue gun, great for filling in hard-to-reach corners.
1. Prepare the mortar
If you are using powdered grout, pour some water into the bucket and add the grout. Stir with a stick, then add the mortar and stir until you get a creamy texture.
2. Mortar construction
Apply grout to the tile with a trowel or grout tool. Take the grout and insert it into the gaps between the bricks. It helps to work diagonally at a 45 degree angle.
important hint: Work on a small area at a time to keep it from drying out until it stays in place.
3. Machining the grouting machine into grooves
The mortar will harden with application, so work on the joints while they still need to be worked on. Be sure to check the drying time on the package and wipe off any excess with a damp sponge. Wait 10 minutes, then use again with a damp sponge.
important hint: Never add water to allow the grout to spread easily, as this will interfere with the spraying process.
You need to seal the joint to make it waterproof. Make sure to use the right sealant for your project; be sure to read the instructions before applying. Simplified connection to two applications. Make sure to wipe off any water droplets from the tile, as some tiles are very sensitive to this substance.
5. Let the grout dry
Let the bricks sit for the recommended time. After drying, polish with a cloth.
how to re-tilt
Never let a pretty white mortar get moldy and dirty for a long time, right? Switch to your style for the weekend, and while you’re at it, why not try something other than white, colorful, or even shiny grout this time around?
Putting the bricks together is easier than you think! Do it yourself with corner grease and grout or one of these finished products.
1. Protected area
Cover the floor with a dust cover to speed up cleaning, and if you’re working in a tub, sink, or sink, plug it into a wall outlet to keep grout out of debris. Open doors and windows for ventilation as there is a lot of dust in the air. If you can’t, wear a protective mask. Wear protective glasses to prevent grout debris from getting into your eyes.
2. Remove old grout
It is possible to remove the mortar with nails, but it is very inconvenient! It’s best to buy or borrow a grout scraper, or better yet, an electric scraper. It’s less labor-intensive, especially if you’re doing the whole room rather than stepping back.
Insert the rake into the grout line starting from the center of the brick. Apply pressure and pull slowly and steadily along the line. If you’re using a power tool, you don’t have to apply pressure, but be sure to choose the correct size tip and be careful not to damage the edges of the tile. Draw vertical lines first, then horizontal lines. Clean the tiles to remove dust.
3. Mix and apply the new screed
If you are using a powder mortar, mix it for as long as possible for 20 minutes (then it will start to harden). Apply a portion of the premixed powder or mortar to the grout tool (use a spatula or mortar). Use a grout machine on the grout and move the tile to the edge to remove excess.
4. Clean and dry
Wipe off excess tile with wet, pressed tile. If the grout comes off, gently push it back with your fingers. Let sit for about half an hour, then use the trowel to cut neat jagged lines – the rounded ends gently pull the grout. Let it dry for a few hours, then use a clean soft cloth to buff any powder residue from the tile surface.
Now your bathroom looks new and you don’t need to spray a new set! Don’t forget to keep it looking its best with our handy mortar cleaning guide.
How to apply mortar to bricks?
As mentioned above, it is best to use a trowel or spreader as this will give the best results.David advises, “Get mortar with suit mortar Floating in the cracks of bricks in all directions Towards Guarantee mortar Completely fill the joint. “
He goes on to give his best advice:
- “Make sure you have enough mortar There are many throughout the territory. “
- “mix mortar Towards wear inside mortar Open Hours (verify correct mix and open hours mortar Package)”
- “Never get caught again mortar.”
How long do you leave the grout in place before cleaning?
It’s best to check the packaging of the grout you’ve chosen for this, but David recommends: “After a few minutes (check the packaging for details), sponge the area.” Wet (but not dirty) damp with a clean hose Water regularly – the cleaner the sponge, the better the tile surface mortar has been removed. “
“test Towards make sure everyone mortar lines are completely filled injection material, otherwise add more mortar After a few minutes, wipe the filled area with a clean damp sponge.
“once mortar start Towards To “bloom” on the surface, wipe the tile surface with a clean dry cloth in a circular motion (check manufacturer’s instructions for exact time Towards “polished” tiles).any excess mortar will become Towards Dust and remove tile from fabric, here’s why it’s important Towards Use plenty of clean cloth. “
“Note: Application interval mortarwipe off excess mortar and polishing/polishing during tiling injection This process can vary greatly depending on temperature, humidity and brick type injectiontype mortar use, tile joint width, etc., so it is important to because Start with an inconspicuous small area Towards Evaluate the possible cure time for each process. “
Is it possible to grout brick over old mortar?
No sewing. For better durability of the machine, you should scrape off the old grout first. If you’re just adding new grout, you’ll notice that as soon as you walk on floor tiles or get wall tiles wet and splash, the grout will start to crack and peel, so you better get the job done. .
Source : idealhome.co.uk